Error Codes of Washer

Washer error codes by brands


We have prepared all the necessary data about almost all makes and models of the washing machine. Search and apply suggestions. It is not possible to overestimate the benefits of the following tables due to a variety of error codes they consist of. I will likely find so many brands in one place.

Bosch Error Codes

Error codeIssueWhat to do
E16/F16Door openClose the door
E17/F17Water overflowingThe tap can be clogged. Inspect the tap and clean it up.
E18/F18Pump time exceededPerform the reset of the washing machine – turn the appliance on and off.
E19/F19Heating issueOne of the obvious causes can be the faulty thermostat. Inspect it and, if needed, replace it.
E20/F20Unexpected heatingReset the washing machine by turning it on and off.
E23/F23Aqua-stop activatedThe appliance is likely to be overloaded.
E25/F25Turbidity sensor issueReplace the turbidity sensor.
E26/F26Problem with the analogue pressure sensorInspect continuity of the sensor using the multi-meter. If it is defective, replace it.
E28/F28Flow sensor issueCheck the voltage of the flow sensor using the multi-meter. Replace it, if there is no continuity.

Samsung Error Codes

Error codeIssueWhat to do
nd, 5EDraining issueThe filter in the drain pump is likely to be clogged. Clean the filter by removing all debris and restrictions.
LODoor issueDisconnect the appliance and open the door. Replace the door latch if it is damaged or worn out.
nF, 4EWater filling issueThe water inlet valve assembly might be defective. Replace the assembly.
FLDoor lock issueInspect the wires connected to the door lock assembly. If they are sound, the door lock assembly has to be replaced.
LEDoor lock issueInspect the wires connected to the door lock assembly. If they are sound, the door lock assembly has to be replaced.
OEWater overflowing issueUnplug the appliance. If the water still keeps flowing, the water inlet valve assembly is faulty. Replace it. Also inspect the water level sensor.
E2, bE2Stuck bottomFree the button by pressing down on the top of the keys on the control board.
tE, tE1Water temperature issueReplace the thermistor (temperature sensor).
SFThe control board issueReset the washing machine, by unplugging it for 5 minutes. Plug in the appliance. If the error code displays again, the control board is faulty. Replace it.

LG Error Codes

Error codeIssueWhat to do
IEInlet water supply issueMake sure the water supply faucets behind the washing machine are open. Inspect the fill hoses whether they don’t have any kinks. The inlet water valves are also to be checked. Replace the defective parts.
UELoading issueRedeploy the clothes in the washing machine. The load has to be balanced. Avoid any overloading or underloading.
OEDraining issueInspect the drain hose whether there aren’t any kinks and restrictions. Disconnect the washing machine and examine the wiring between the control board and the drain pump. Change the defective wires. Replace the drain pump, if it is malfunctioning.
FEWater overflowing issueInspect the inlet water valves to learn whether they cut off the water supply after the washing machine is filled. If the valves are faulty, you are to replace the inlet water valve assembly.
dEDoor failureUnplug the washing machine and examine the door. In case the door is damaged, replace the faulty components. Examine the door lock (switch assembly wiring). If the wires are sound, replace the door lock (switch assembly).
tEHeating sensor issueExamine the wiring of the thermistor sensor, having checked it continuity using the multi-meter. The measures should be 40,000 ohms at 85 degrees Fahrenheit. Replace the thermistor, it is out of order.
PFPower issueThe power outage could occur in the process of cycling. Restart the appliance.

Electrolux Error Codes

Error codeIssueWhat to do
E11, E12Water filling issueOpen the tap, it is likely to be closed. Another obvious reason can be the low water pressure. Also check the water fill solenoid valve. Replace the valve, if it is faulty.
E13Water leaking issueCheck the drain hose for the kinks and restrictions. Also examine the pressure switch that is likely to be faulty. Replace the defective pressure switch.
E35Water overflowing issueThe water fill solenoid is malfunctioning. Replace it.
E38Pressure chamber blockedThe motor drive belt is supposedly damaged or worn out. Replace it.
E74NTC sensor issueMake sure the NTC sensor is fitted properly. Check its continuity with multi-meter. If it is defective, replace it.

Kenmore Error Codes

Error codeIssueWhat to do
F0 E2Undue sudsUse only the high quality detergent. To prevent suds, use the sufficient quantity of detergent.
F0 E4Water temperature issue (during the rinse cycle)Check whether the fill hoses are fitted properly. Inspect the temperature sensor (thermistor) – the measure should be around 50,000 ohms at 77 degrees Fahrenheit. If the temperature sensor is faulty, replace it.
F0 E5Loading issueEnsure you didn’t overload the washing machine. Inspect the suspension rods and springs. If they are damaged or worn out, replace them.
F1 E1Control board failureUnplug the washing machine and inspect the wiring connections of the control board. Replace the control board, if the wires are damaged.
F1 E2Motor control issueInspect the drive motor windings for its resistance. If the motor is defective, replace it. Otherwise, you should replace the main electronic control board.
F2 E1Stuck key issueIf the stuck key cannot be freed up, replace the user interface control.
F3 E1Water level pressure sensor issueOpen the console and check the thermistor for its resistance – it has to be 50,000 ohms at room temperature. If the thermistor is malfunctioning, replace it.

Maytag Error Codes

Error codeIssueWhat to do
F1 E1Control board issueReset the washing machine by unplugging the appliance for 5 minutes. Plug in. If the error code shows up again, you are to replace the main electronic control board.
F1 E2Motor control board issueInspect the wiring on the motor control board. If the wires are not sound, the motor control board needs to be replaced.
F3 E1Water level pressure switch issueExamine the wire harness between the water level pressure switch and the control board. If the wire harness is damaged, replace it. If the wiring is ok, the water level pressure switch is to be replaced.
F3 E2Temperature sensor issueUnplug the washing machine and inspect the wiring connected to the temperature sensor. Reconnect the loose wires. If the wiring is sound, you have to replace the temperature sensor.
F5 E1Door switch issueInspect the door lock/switch and replace it, if it appears to be defective.
F6 E2 / F6 E3Communication error between the control board and the user interface control.Inspect the wire harness between the main control board and the user interface control. Any loose wires need to be reconnected. If the wire harness is damaged, replace it.

Whirlpool Error Codes

Error codeIssueWhat to do
IntThe cycle is cancelled or pausedPress the pause button or the cancel button twice and the power button once. If the error code is still showing up, unplug the washing machine for one minute.
rL / F34There are found within the clean washer cycle.Any items need to be removed from the drum. Restart the clean washer cycle.
Sud / Sd Sud / Sd Excessive sudsUse only the high efficiency detergent. Also check the drain hose for the kinks and restrictions.
F8 E2Dispenser System issueMake sure the detergent drawer or detergent cartridge is not plugged up with detergent. Remove the clogged detergent from drawer and cartridge.

If you are still struggling with the washer problem or repair on your own seems to be daunting, the courteous professionals of Care&Repair are always on service to help you. Give us a call or email us any convenient time for you. We work 24/7.